- Español
- Português
- русский
- Français
- 日本語
- Deutsch
- tiếng Việt
- Italiano
- Nederlands
- ภาษาไทย
- Polski
- 한국어
- Svenska
- magyar
- Malay
- বাংলা ভাষার
- Dansk
- Suomi
- हिन्दी
- Pilipino
- Türkçe
- Gaeilge
- العربية
- Indonesia
- Norsk
- تمل
- český
- ελληνικά
- український
- Javanese
- فارسی
- தமிழ்
- తెలుగు
- नेपाली
- Burmese
- български
- ລາວ
- Latine
- Қазақша
- Euskal
- Azərbaycan
- Slovenský jazyk
- Македонски
- Lietuvos
- Eesti Keel
- Română
- Slovenski
- मराठी
- Srpski језик
Battery Material Flash Dryer
The following is an introduction to Battery Material Flash Dryer, I hope to help you better understand Battery Material Flash Dryer. Welcome new and old customers to continue to cooperate with us to create a better future together!
Send Inquiry
Product Description
Battery material flash dryer
FEATURES
1. Organic combination of swirl, fluidization, spouting and crushing classification technology.
2. Compact equipment, small volume, high production efficiency, continuous production, small equipment, large-scale production
3. High drying intensity, low energy consumption and high thermal efficiency.
4. Short residence time of materials and good quality of finished products can be used for drying heat sensitive materials.
5. Negative pressure or micro negative pressure operation, good sealing, high efficiency, eliminate environmental pollution.
6. Heating mode: steam, electric heating, heat transfer oil
7. Material: stainless steel, titanium, carbon steel
8. According to the customer and process requirements, customized
WORKING PRINCIPLE
The hot air enters into the bottom of the drier in tangent direction. Under the driving of the stirrer, a powerful rotating wind field is formed. The paste state materials enter into the drier through the screw feeder. Under the powerful function of the stirring vanes at high-speed rotation, the materials are distributed under the function of strike, friction and shearing force. The cake state materials will be smashed and contact the hot air fully and the materials are heated and dried. The dehydrated materials will go up with the hot-air flow. The step rings will stop and keep the big particles. Small particles will be discharged out of the drier from the center of the machine and the material will be collected by cyclone separator of dust collector. The wet or big particles will be swing towards to the wall by the centrifugal force function and the materials will be crushed again after fall down to the bottom.
APPLICATION
It is applicable to organic, inorganic, dye, food, chemical, pharmaceutical and other industries
TECHNICAL PARAMETERS
|
Item \ Model |
XSG-2 |
XSG-4 |
XSG-6 |
XSG-8 |
XSG-10 |
XSG-12 |
XSG-16 |
XSG-20 |
|
Tower Diameter (mm) |
200 |
400 |
600 |
800 |
1000 |
1200 |
1600 |
2000 |
|
Air amount (M3/h) |
350-500 |
1150-2000 |
2450-4500 |
4450-7550 |
7000-12500 |
10000-20000 |
18000-36000 |
28200-56500 |
|
Water Evaporation (kg/h) |
12-17 |
40-70 |
80-150 |
150-250 |
230-4250 |
300-600 |
600-1000 |
1000-1500 |
|
Total Power (kW) |
10 |
20 |
40 |
65 |
85 |
105 |
150 |
230 |
|
Max. Equipment Height (m) |
4.0 |
4.8 |
5.8 |
6.5 |
7.1 |
7.8 |
8.8 |
10.1 |
|
Occupied Area (m2) |
15 |
20 |
28 |
35 |
40 |
52 |
80 |
150 |
Note:
1. The evaporated amount of moistureis calculated when the temperature of inlet is l80oC and Ihe temperature of outlet is180oC and the temperature of outlet is 180oC;
2. Besides the models above mentioned, special specification can also be made as request;
3. The equipped capacity above mentioned is standard. The power can also be decreased in accordance with pracitcal condition.
Raw Material Example & Characteristics (based on Model XSG-6)
|
Item \ Raw Material |
Stearate Acid |
Aluminum hydroxide |
Zinc Carbonate |
Monosultap |
TMTD |
DSD |
Red Iron Oxide |
Antimony |
Cuprous |
White |
|
Inlet Air Temperature (oC) |
150 |
180 |
150 |
120 |
140 |
150 |
200 |
180 |
200 |
280 |
|
Primary Moisture (%) |
80 |
55 |
80 |
30 |
65 |
60 |
60 |
45 |
30 |
85 |
|
Final Moisture (%) |
0.5 |
1.5 |
1.0 |
1.0 |
0.5 |
0.5 |
0.5 |
1.0 |
3.0 |
5.0 |
|
Practical Drying Capacity (kg/h) |
140-160 |
250-280 |
130-170 |
80-110 |
80-120 |
80-120 |
300-350 |
280-320 |
290-310 |
250-300 |
|
Item \ Raw Material |
ZDC |
Oil |
Substitute |
Phthaloc- |
Calcium |
Superfine |
Slurry |
Sodium |
|
|
Inlet Air Temperature (oC) |
150 |
150 |
120 |
150 |
140 |
160 |
200 |
180 |
150 |
|
Primary Moisture (%) |
60 |
45 |
30 |
55 |
40 |
70 |
75 |
25 |
30 |
|
Final Moisture (%) |
0.5 |
2.0 |
1.0 |
1.0 |
1.0 |
1.5 |
5.0 |
0.2-2 |
1.0 |
|
Practical Drying Capacity (kg/h) |
80-110 |
350-380 |
120-150 |
160-180 |
300-350 |
430-470 |
290-310 |
80-120 |
90-150 |
